axtoc03
Oscillator
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. axtoc03 is a 2…5MHz crystal oscillator for voltage range from 3.5V to 5.5V.
aporc01
Power On/Off Reset
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. aporc01 is a digital power-on-reset circuit. During power-on, POR output is kept high as long as the supply voltage is below the POR threshold voltage. After the threshold has been reached, the POR signals turns low. A delay of
aporc02
Power On/Off Reset
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. aporc02 is a digital power-on-reset circuit. PORB output is kept low as long as the supply voltage is below the POR threshold voltage. PORB signal is generated on both rising and falling edges of the supply voltage. During power
aporc04
Power On/Off Reset
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. aporc04 is a digital power-on-reset circuit. PORB output is kept low as long as the supply voltage is below the high POR threshold voltage. PORB signal is generated on both rising and falling edges of the supply voltage. During
apogc01
Power On/Off Reset
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. apogc01 is a general purpose, power good detector. A power good signal (active high) is generated as long as the supply voltage at the VDDA pin lies within the 4.5V - 5.5V limits. When the supply voltage is beyond the either low
adacc01
DAC
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. adacc01 is a 8-bit digital-to-analog converter (DAC) with a R-2R ladder network. The DAC operates with a single 5V supply and external reference voltage.
adacc02
DAC
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. adacc02 is a 10-bit digital-to-analog converter (DAC) with a R-2R ladder network. The DAC operates with a single 5V supply and external reference voltage.
adacc03
DAC
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. adacc03 is a 8-bit voltage-scaling digital-to-analog converter (DAC). The device can operate at supply and reference voltages down to 3.2V.
aregc01
Voltage Regulator
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. aregc01 is a 5V / 3.3V positive voltage linear regulator for up to 10 mA load current.
aregc02
Voltage Regulator
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. aregc02 is a 2.4V / 3.3V positive voltage switching regulator for on-chip loads and up to 10 mA load current.
adrvc01
Driver
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. adrvc01 is a driver circuit for external loads (relays, LEDs, etc). The circuit features NMOS open-drain output. The rising slope of the output signal can be controlled by means of a bias current.
atmpc01
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. atmpc01 is a high-temperature detector. An OVERT output signal (active low) is generated when the chip temperature rises above 140 °C (approx.).
atmpc02
X-FAB
1.00 µm
XC10
PT
Schematic
Layout
Analog Library
XC10: A_CELLS; A_CELLS_M1. atmpc02 is a high-temperature detector. An OVERT output signal (active low) is generated when the chip temperature rises above 160 °C (approx.).
D17IP15
Voltage Regulator
Desert Microtechnology
1.00 µm
XC10
MP
GDSII
Schematic
D17IP15 is a voltage regulator with built in reference. Has 5V low drop out regulator that can operate from 5.5V - 25V supply. Has 14V regulator when the supply is > 25V. Can be paired with D17IP16 to generate a voltage oscillator.
D17IP16
Oscillator
Desert Microtechnology
1.00 µm
XC10
MP
GDSII
Schematic
D17IP16 is a voltage oscillator at 500 kHz. It requires 3 input reference voltages 1.064V, 1.275V and 0.762V. These voltages can be generated with the D17IP15. Output is to designed to drive on chip light loads.
aopac01
Operational Amplifier
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Aopac01 is a general purpose internally compensated CMOS OpAmp with PMOS input stage and NPN emitter-follower output stage.
abiac02
Bias
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Abiac02 is a general purpose bias cell. It forces a current of 2µA to flow through PMOS with W/L ratio of 10µm/8µm and NMOS with W/L ratio of 10µm/12µm.
abiac04
Bias
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Abiac04 is a general purpose bias cell. It forces a current of 10µA to flow through PMOS with W/L ratio of 12µm/4µm and NMOS with W/L ratio of 12µm/6µm.
abiac06
Bias
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Abiac06 is a general purpose bias cell. It forces a current of 200nA to flow through PMOS with W/L ratio of 10µm/12µm and NMOS with W/L ratio of 8µm/20µm.
acsoc02
Current Source
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Acsoc02 is a general purpose current source. It provides a set of four binary-weighted output currents 1, 2, 4, & 8µA.
acmpc01
Comparators
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Acmpc01 is a compact low-power CMOS comparator with hysteresis. The input stage is PMOS differential pair.
acmpc02
Comparators
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Acmpc02 is a compact low-power CMOS comparator with hysteresis. The input stage is NMOS differential pair.
acmpc03
Comparators
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Acmpc03 is a rail-to-rail CMOS comparator.
acmpc04
Comparators
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Acmpc04 is a current-programmable rail-to-rail CMOS voltage comparator. The speed and power consumption of cell are programmed by means of bias current.
aadcc01
ADC
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Aadcc01 is a 10-bit successive approximation Analog-to-Digital converter (ADC). The ADC operates with a single 5V power supply and an external voltage reference.
adacc01
DAC
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Adacc01 is a 10-bit voltage-scaling (potentiomentric) Digital-to-Analog converter (DAC). The cell operates with a single 5V power supply & external reference voltage.
adacc02
DAC
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Adacc02 is a 8-bit R-2R Digital-to-Analog converter (DAC). The cell operates with a single 5V power supply & external reference voltage.
adacc03
DAC
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Adacc02 is a 10-bit R-2R Digital-to-Analog converter (DAC). The cell operates with a single 5V power supply & external reference voltage.
arcoc01
Oscillator
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Arcoc01 is a robust 1MHz current-balancing RC oscillator with internal R and C. The cell features small die area, very low temperature coefficient of clock frequency and moderate power consumption.
arcoc02
Oscillator
X-FAB
1.00 µm
XDH10
PT
Schematic
Layout
Analog Library
XDH10: A_CELLS. Arcoc02 is a 1MHz adjustable current-balancing RC oscillator with internal R and C. The cell features small die area, very low temperature coefficient of clock frequency and moderate power consumption.