IP Portal

The core realized the I²C-bus protocol

Features:

Master and receive mode realized

Bus node address and data transmission rate are programmable

8 Bit data interface to the controller

All I²C function are implemented

Core is multimasterable   

XC018 LP 3.3V atmpc01_3v3 is an over-temperature detector. When the chip temperature rises over the high threshold temperature (~130°C) the output signal turns high.

XC018 LP 5V atmpc01_5v is an over-temperature detector. When the chip temperature rises over the high threshold temperature (~125°C) the output signal turns high.

Low consumption combo voltage and current reference core. The circuit generates an unbuffered 1.29V, temperature compensated voltage reference (70ppm/°C) and provides a 1.6μA PMOS current branch (200ppm/°C).

General purpose capacitive sensor core. The circuit is intended for touch sensing applications for use in microcontrollers and has two multiplexed inputs. 3pF input sensibility and output frequency of 460kHz - 600kHz.

30V/20mA Power Driver/Switch - Two modes of operation: switch or programmable current output; short-circuit protection, over-current detection.

250kHz PWM for DC-DC converters

High Voltage Input for input voltages up to 100V

SA00PFC000 is a PLL with internal loop filter. Wide output clock freq. range : 10MHz～200MHz. Wide input clock freq. range : 2MHz～50MHz

SA00PFC010 is a PLL with internal loop filter. Wide output clock freq. range : 10MHz～160MHz. Wide input clock freq. range : 2.5MHz～6MHz.

XB06: LNA library: RF_PA_CELLS. PA is a non-linear Power Amplifier that is intended for the transmission of ASK and FSK signals. Its output power level can be digitally controlled in 4 steps. It should be biased by the RF bias cell.

XC10: A_CELLS; A_CELLS_M1. aporc01 is a digital power-on-reset circuit. During power-on, POR output is kept high as long as the supply voltage is below the POR threshold voltage. After the threshold has been reached, the POR signals turns low. A delay of

XC10: A_CELLS; A_CELLS_M1. aporc02 is a digital power-on-reset circuit. PORB output is kept low as long as the supply voltage is below the POR threshold voltage. PORB signal is generated on both rising and falling edges of the supply voltage. During power

XC10: A_CELLS; A_CELLS_M1. aporc04 is a digital power-on-reset circuit. PORB output is kept low as long as the supply voltage is below the high POR threshold voltage. PORB signal is generated on both rising and falling edges of the supply voltage. During

XC10: A_CELLS; A_CELLS_M1. apogc01 is a general purpose, power good detector. A power good signal (active high) is generated as long as the supply voltage at the VDDA pin lies within the 4.5V - 5.5V limits. When the supply voltage is beyond the either low

XC06: A_CELLS. aporc01 is a dynamic Power-on-Reset circuit. During power-on, POR output is kept high as long as the supply voltage is bellow the POR threshold voltage. When the threshold voltage is reached, the POR signal turns low. A delay of few microse

XC06: A_CELLS. aporc02 is a Power-on-Reset circuit with hysteresis. Reset signals are generated on both the rising and falling edge of the supply voltage. During power-on, POR output is kept high as long as the supply voltage is bellow the high threshold

XC06: A_CELLS. aporc03 is a Power-on-Reset circuit. Reset signals are generated on both the rising and falling edge of the supply voltage. During power-on, POR output is kept low as long as the supply voltage is bellow the threshold voltage. When the high

XH035: A_CELLS. For MOS module only. aporc01 is a dynamic Power-on-Reset circuit. During power-on, POR output follows the supply voltage as long as it is below the threshold voltage. When the threshold voltage is reached, the POR signal turns low. A delay

XH035: A_CELLS. For MOS module only. aporc02 is a Power-on-Reset circuit with hysteresis. Reset signals are generated on both the rising and falling edge of the supply voltage. During power-on, POR output follows the supply voltage as long as it is b

XH035: A_CELLS. For MOS module only. aporc03 is a Power-on-Reset circuit. Reset signals are generated on both the rising and falling edge of the supply voltage. During power-on, POR output follows the supply voltage as long as it is below the threshold v

XC018 LP 5V aporc01_5v is a dynamic Power-on-Reset (POR) circuit. During power-on, POR output follows the supply voltage as long as it is below the threshold voltage. When the threshold voltage is reached, the POR signal turns low.

XC018 LP 5V aporc02_5v is a Power-on-Reset (POR) circuit with hysteresis. Reset signals are generated on both the rising and falling edge of the supply voltage.

XC018 LP 5V aporc03_5v is a Power-on-Reset (POR) circuit. Reset signals are generated on both the rising and falling edge of the supply voltage.

XT06 aporc01 is a dynamic Power-on-Reset circuit. During power-on, POR output is kept high as long as the supply voltage is below the POR threshold voltage. When the threshold voltage is reached, the POR signal turns low.

XT06 aporc02 is a Power-on-Reset circuit with hysteresis. Reset signal are generated on both the rising and failing edge of the supply voltage. During power-on, POR outputs is kept high as long as the supply voltage is below the threshold voltage.

XT06 aporc03 is a Power-on-Rest circuit. Reset signals are generated on both the rising and falling edge of the supply voltage. During power-on, POR output is kept high as long as the supply voltage is below the high threshold.

Power On Reset cell

XC018 LP 3.3V aporc01_3v3 is a dynamic power-on-reset circuit (POR). The cell is suitable for applicaitons where low consumption is important.

XC018 LP 3.3V aporc02_3v3 is a Power-on-Reset circuit with hysteresis. Reset signals are generated on both the rising and falling edge of the supply voltage.