IP Portal

XT06 arcoc07 is a 10kHz low-power oscillator with internal R and C.

XT06 arcoc08 is a 10MHz low-power oscillator with internal R and C.

XT06 arcoc09 is a 20MHz low-power oscillator with internal R and C.

XT06 axtoc01 is a 32kHz crystal oscillator for 3.5 to 5.5V supply voltage range. An external quartz has to be connected to XTALIN and XTALOUT pins.

XT06 axtoc02 is a 1...4MHz crystal oscillator for supply voltage range from 3.5 to 5.5V. An external quartz crystal as to be connected to XTALIN and XTALOUT pins.

XT06 axtoc03 is a 1...6MHz crystal oscillator for supply voltage range from 3.3 to 5.5V. An external quartz crstal has to be connected to XTALIN and XTALOUT pins.

XT06 aporc01 is a dynamic Power-on-Reset circuit. During power-on, POR output is kept high as long as the supply voltage is below the POR threshold voltage. When the threshold voltage is reached, the POR signal turns low.

XT06 aporc02 is a Power-on-Reset circuit with hysteresis. Reset signal are generated on both the rising and failing edge of the supply voltage. During power-on, POR outputs is kept high as long as the supply voltage is below the threshold voltage.

XT06 aporc03 is a Power-on-Rest circuit. Reset signals are generated on both the rising and falling edge of the supply voltage. During power-on, POR output is kept high as long as the supply voltage is below the high threshold.

XT06 achpc01 is a doubling charge pump 3.3V => 5.6V.

XC018 LP 3.3V abgpc01 is a general purpose low-power bandgap reference with N-well resistors.

XC018 LP 3.3V abgpc02 is a general purpose low-power bandgap reference with rnp1 resistors

XC018 LP 3.3V abgpc03 is a low-voltage bandgap reference with N-well resistors.

XC018 LP 3.3V aopac03_3v3 is a general purpose internally compensated rail-to-rail input, rail-to-rail output CMOS operational amplifier (OpAmp). The speed, gain bandwidth, and the power consumption of the amplifier are set by means of a bias curren

XC018 LP 3.3V aopac06_3v3 is a general purpose internally compensated rail-to-rail input, rail-to-rail output CMOS operational amplifier (OpAmp).

XC018 LP 3.3V aopac07_3v3 is a general purpose internally compensated rail-to-rail input, railt-to-rail ouput CMOS operational ampl;ifier (OpAmp).

XC018 LP 3.3V aopac08_3v3 is a general internally compensated NMOS input, rail-to-rail output CMOS operational amplifier (OpAmp).

XC018 LP 3.3V aopac09_3v3 is a general purpose internally compensated PMOS input, rail-to-rail output CMOS operational amplifier (OpAmp).

XC018 LP 3.3V axtoc01_3v3 is a robust 32.768 kHz crystal oscillator for supply voltage range from 2.4 to 3.6V.

XC018 LP 3.3V aporc01_3v3 is a dynamic power-on-reset circuit (POR). The cell is suitable for applicaitons where low consumption is important.

XC018 LP 3.3V aporc02_3v3 is a Power-on-Reset circuit with hysteresis. Reset signals are generated on both the rising and falling edge of the supply voltage.

XC018 LP 3.3V aporc03_3v3 is a Power-on-Rest circuit. Reset signals are generated on both the rising and falling edge of the supply voltage.

XC01801_3v3 is a 3.3V/1.8V linear voltage regulator for up to 20mA load current and internal bandgap reference. The regulator is implimented as a macro cell that fits into the core-limited I/O ring.

XC018 LP 3.3V atmpc01_3v3 is an over-temperature detector. When the chip temperature rises over the high threshold temperature (~130°C) the output signal turns high.

XC018 LP 3.3V avcoc01_3v3 is a voltage controlled oscillator (VCO).

This IP is a cyclic ADC based on RSD algorithm usable as core for embedded applications. The special advantage of this type of ADC is the reduced complexity of hardware resp. layout area because of the reuse of the main stages for each bit. Up to 13 bit o

DC/DC regulator.

DC/DC Buck Regulator with 0% to 100% duty cycle.

Bandgap Voltage Reference and Current Bias Cell.

Current Reference and Current Biasing Cell.