IP Portal

XH035: A_CELLS. For MOS module only. axtoc01 is a robust 2 - 8 MHz crystal oscillator for supply voltage range from 2.4 to 3.6V. An external quartz crystal is required.

XT06 axtoc01 is a 32kHz crystal oscillator for 3.5 to 5.5V supply voltage range. An external quartz has to be connected to XTALIN and XTALOUT pins.

XC018 LP 3.3V axtoc01_3v3 is a robust 32.768 kHz crystal oscillator for supply voltage range from 2.4 to 3.6V.

XC018 LP 5V axtoc01_5v is a robust 32.7689 kHz crystal oscillator for supply voltage range from 3.5V to 5.5V.

XC10: A_CELLS; A_CELLS_M1. axtoc02 is a 1…2MHz crystal oscillator for voltage range from 3.5V to 5.5V.

XC06: A_CELLS. axtoc02 is a 1...4 MHz crystal oscillator for supply voltage range from 3.5 to 5.5V An external quartz crystal has to be connected to the XTLIN and XTALOUT pins. No other external components are required.

XH035: A_CELLS. For MOS module only. axtoc02 is a robust 32,768kHz crystal oscillatior for supply voltage range from 2.4 to 2.6V. An external quartz crystal is required.

XT06 axtoc02 is a 1...4MHz crystal oscillator for supply voltage range from 3.5 to 5.5V. An external quartz crystal as to be connected to XTALIN and XTALOUT pins.

XC018 LP 3.3V axtoc02_3v3 is a robust 1-4 MHz crystal oscillator for supply voltage range from 2.4 to 3.6V.

XC018 LP 5V axtoc02-5v is a robust 1-4 MHz crystal oscillator for supply voltage range from 3.5V to 5.5V.

XC10: A_CELLS; A_CELLS_M1. axtoc03 is a 2…5MHz crystal oscillator for voltage range from 3.5V to 5.5V.

XC06: A_CELLS. axtoc03 is a 2...6 MHz crystal oscillator for supply voltage range from 3.5 to 5.5V. An external quartz crystal has to be connected to the XTALIN and XTALOUT pins. No other external components are required.

XT06 axtoc03 is a 1...6MHz crystal oscillator for supply voltage range from 3.3 to 5.5V. An external quartz crstal has to be connected to XTALIN and XTALOUT pins.

XC06: A_CELLS.

XB06: LNA library: RF_BIAS_CELLS. BIAS is a bias cell intended for use with various RF building blocks. It is designed as a bandgap reference as well as voltage-to-current converter. Current biasing is preferable because of the higher immunity to interfer

XH035: BIAS Library: RF_BIAS_CELLS. BIAS is a bias cell intended for use with the various RF building blocks. It is based on a bandgap reference and voltage-to-current converters. Current biasing is preferable because of the higher immunity to interferenc

General purpose linear voltage regulator. The circuit generates a 3.3V output voltage from an unregulated input voltage ranging from 5V to 30V. It features short circuit protection and 5mA output current capability.

2Low consumption Power-On Reset (POR) core. The core has a voltage sense (configurable 0.9V - 5.5V), an internal current bias circuit and two configurable assertion delays (default are > 1μs and > 20μs). A configurable hysteresis (default 100mV).

Low consumption combo voltage and current reference core. The circuit generates an unbuffered 1.29V, temperature compensated voltage reference (70ppm/°C) and provides a 1.6μA PMOS current branch (200ppm/°C).

Low power, general purpose, 10-bit, 50kSPS, Successive Approximation Register (SAR) Analog-to-Digital Converter (ADC) core. The circuit uses one 3.3V analog supply and one 3.3V digital supply and is targeted for microcontroller applications.

General purpose, low power internal oscillator core, 12MHz. The circuit has internal level shifting and start-up circuits. A 4-bit digital bus allows frequency calibration against process variations. Current consumption <40μA, supply voltage 2.7V-3.6V

General purpose capacitive sensor core. The circuit is intended for touch sensing applications for use in microcontrollers and has two multiplexed inputs. 3pF input sensibility and output frequency of 460kHz - 600kHz.

30V/20mA Power Driver/Switch - Two modes of operation: switch or programmable current output; short-circuit protection, over-current detection.

CX08A: Analog library. DAC10 is a 10-bit digital-to-analog converter. The architecture is based on two resistor dividers. Because of its high output impedance, which is also code dependent, a low offset buffer operational amplifier is strictly recomm

XB06: A_CELLS. DAC10 is a 10-bit digital-to-analog converter. The architecture is based on two resistor dividers. Because of its high output impedance, which is also code dependent, a low offset buffer operational amplifier is strictly recommended at the

XB06: A_CELLS. DAC6rs is a 6-bit digital-to-analog converter. The architecture is based on a resistor divider. The output impedance is code dependent.

CX08A: Analog library. DAC8 is a 8-bit digital-to-analog converter. The architecture is based on two resistor dividers. Because of its high output impedance, which is also code dependent, a low offset buffer operational amplifier is strictly recommen

XB06: A_CELLS. DAC8 is a 8-bit digital-to-analog converter. The architecture is based on two resistor dividers. Because of its high output impedance, which is also code dependent, a low offset buffer operational amplifier is strictly recommended at the ou

XB06: A_CELLS. DAC8rs is a 8-bit digital-to-analog converter. The architecture is based on a resistor divider. The output impedance is code dependent.

XB06: LNA library: RF_DIVIDER_CELLS. DIV32 is a Prescaler with a fixed divider ratio of 32. It should be biased by the RF bias cell.